Low Current Triggered Transmitter and 1 Channel Long Range Receiver Controls LED Runway Lights at Private Airport

Overview:

"I am looking for a remote and multiple receivers for a small private airport. We have a controller box switch that activates when you key the microphone 7 times on a specific frequency. I would like to plug a dc power adapter into this unit and wire into one of your remotes. The runway lights are all solar dc leds. I will need 12 receivers total to start out. My question is: Can one remote, controlled by external wires, send a signal out to multiple receivers at the same time?  In other words, if the remote detects dc input and sends out an ON signal, can several receivers receive the ON signal at the same time?”

Solution:

We recommend the low current triggered transmitter (CB-2V) and 1 channel long range receivers (S1L-DC12-ANT2). The most remarkable feature of this transmitter is low current triggered. That is to say, when you offer dc power 5~28V to this transmitter, it will send signal out to the receiver. The receiver is long range with external extended antenna. When it works in pairs with transmitter, their transmitting distance can reach 2000m (6000ft) in the open field. One transmitter can send out ON signal to make several receivers ON at the same time if you use the same code of those transmitter and receivers.

Wires on the transmitter should be connected to the contacts of original device which can generate dc 5~28V output power.

The normally open contacts B&C of receivers should be connected to solar led light being controlled. Wire each solar led light to each receiver.

When the contacts of two wires of transmitter input 5~28V voltage, the transmitter is triggered and then transmits an rf signal “ON” to the receiver. After the receiver receives the signal, contacts B&C are closed; the solar led lights being controlled starts to work.

When the contacts of two wires of transmitter’s power is cut, the transmitter is triggered and then transmits an rf signal “OFF” to the receiver. After the receiver receives the signal, contacts B&C are cut; the solar led lights being controlled stops working.

Online shop: www.carymart.com

Long Range Remote Control Water Pump

Question from customer:

I am looking for a long range relay to control a water pump. The water pump now is controlled by a float switch (on/off) at the reservoir 800 meters away. I have 120 volts at both locations and a relay to start pump.

Answer:

We recommend the 2000m rf AC receiver (S1PUA-AC220-ANT2) and the long range transmitter CB-2N. The receiver is soldered with external extended antenna, which can make its transmission distance at 2000m/6000ft theoretically. It works between AC 100~240V voltage. The maximum working current is 30amps. There are 315Mhz or 433Mhz at your option. The transmitter is special designed because its triggered method is connection and disconnection of two wires. When two wires are connected, the transmitter is triggered and then transmits an rf signal “ON”. When two wires are disconnected, the transmitter is triggered and then transmits an rf signal “OFF”.

The wiring method of your water pump will be talked next.

A, B terminals are normally open; A, C terminals are normally closed. Wire Water pump motor to A terminal and N terminal. Add wire to connect B&L terminals. Supply AC 100~240V power to receiver. Connect two wires of transmitter to relay you mentioned.

Usage:

When two wires of transmitter are connected, the transmitter is triggered and then transmits rf signal “ON”; When the receiver accepts the signal, it will make water pump work.

When two wires of transmitter are disconnected, the transmitter is triggered and then transmits an rf signal “OFF”. When the receiver accepts the signal, it will stop water pump.

Online shop: www.carymart.com

1 Channel DC Long Range Remote Control Gadget Controls Flashing LED to Scare Birds

Question from customer:

I want to use the 1 channel remote control to operate flashing LEDs in a tree to scare

birds in the evening from roosting.

Answer:

It is a good idea to scare birds from roosting in the evening by remote controlling a flashing LED because you must be very furious at noise to spoil your sweet dream or interfere with your other activities. Our suggestion is that you can choose this 1 channel dc triggered long distance remote gadget (S1X-DC12-ANT2+CB-2). You can wiring one flashing LED to relay channel. Flashing LED can get power from receiver directly. With external extended antenna, this remote gadget will transmit signal up to 2000m (6000ft) in the open field.

Here is the wiring diagram. Flashing LED is connected to terminals A&B of receiver. And supply power to receiver.

Operation:

There are two working modes for your information. They are momentary and latched modes.

1. Setting control mode Momentary: Only connect Jumper-1.

Press and hold big button: Turn on the relay, terminal A&B output DC power. The flashing LED will keep flashing constantly.

Release big button: Turn off the relay, terminal A&B no output. There is no flashing from LED.

2. Setting control mode Latched: Do not connect Jumper-1 and Jumper-2. Press big button: Turn on the relay, terminal A&B output DC power. The flashing LED will be remote controlled and keep flashing all the time.

Press small button: Turn off the relay, terminal A&B no output. The LED is off.

Online shop: www.carymart.com

Long Range Single Channel Remote Controls Doorbell

Question from customer:

I want to install a single channel remote to control my doorbell within the range of 100m. The old 12V doorbell was broken because of the construction which cannot be repaired. Ordinary wireless doorbell cannot be used because of distance. I have an idea that a transmitter is connected to the doorbell button and relay in receiver is connected to doorbell. The only problem is the control range of remote need to reach about 100m. Would you like to recommend some favorable products?

Answer:

We recommend the long range dc power receiver S1U-DC12-ANT2 and one button transmitter CP-1.

Working voltage range of receiver is 12V. With normally open and close terminal, the voltage of the device being controlled is AC110~240V or DC0~28V. So it can be applied in 12V doorbell. And the most significant is that it has extended external antenna which makes its control range up to 2000m (6000ft). You will be satisfied with this product.

According to your requirement, you can connect the button of the bell to the transmitter by two wires. Then connect the bell to the relay in the receiver.

Setting control mode Momentary: Connect Jumper-1.

When you press the button of the bell, RF signal will be sent out from transmitter to receiver. The receiver receives to turn on the relay, then the doorbell rings. Release the button, the doorbell stops ringing.

Online shop: www.carymart.com

Great Range Remote Control Lights in Basement

Question from customer:

I want to remote control two lights which are both 90W 220V in the basement from the ground floor. So I need to buy a set remote controller kit. It will be installed in the basement and will be controlled by one controller. I can control  from the ground floor leisurely and carefree. What’s your suggestion?

Answer:

Our suggestion is the kind of great range remote controller set.

Its receiver is 2 channels and with external extended mount antenna. And its transmitter has 2 buttons. At first, you can do some wiring according to our application circuit.

Operation:

You can choose “Toggle Mode”. Only connect Jumper-2.

Press big button: Turn on the light 1. Press big button again: Turn off the light 1.

Press small button: Turn on the light 2. Press small button again: Turn off the light 2.

That is so easy to operate.

Online shop: www.carymart.com 

Long Range Remote Control System is used in Metal Shed House

Our remote control system product, S1PUA-AC220-ANT2 & CB-2 was purchased by one of our customers recently. He said that he was so happy with the items because of its good performance. What’s more, he also satisfied with our fast delivery and product tracking service.

The receiver is high power with maximum working current of 30A. It has three working modes which are toggle mode, momentary mode and latched mode. The RF signal can pass through walls, doors, floors, trees and so on. With the external mount antenna, the receiver pairs with long range transmitter-CB-2. Remote control distance of transmitter & receiver set is up to 2000m in open field. That customer said that it is more importantly for remote control kit is to work well even in his metal shed house.

For installation of a device controlled by remote controller in his house, that customer also has tried other brands’ RF products but none of them can work as well as ours.  Thanks to this external extend antenna design, it enhances RF signal’s transmitting and makes excellent performance.

The wiring is not complicated. Just do as the following picture.

Lamp or other devices should be connected to normally open terminal A&B at first. Then we wire up the receiver. Press big button on the transmitter, the lamp or other devices will on; Press small button on the transmitter, the lamp or other devices will off.

Online shop: www.carymart.com

Automatically control lamps with feedback function in Long Range (3 miles)

If you want to automatically control lamps in long range with feedback function, we suggest you a new long range remote control kit: model 0020105(S2PUW-DC12-ANT2 & 1CC-2). This kit contains one receiver, one transmitter and magnetic sucker antenna.
Here is the long range automatic control kit:

The long range automatic remote control kit can be used in agriculture automation, industry automation, and home automation, such as security system, remote control lights, motors, doors/ locks/ windows/ blinds/ cars and various equipments. The working distance of automatic remote control kit is between 1000m and 5000m. The remote control kit has waterproof case with waterproof connectors. The receiver can be installed outdoors. It can control products on land, water and air, especially in a long distance, such as business signs, motorboat, farm, pasture, offshore unmanned operation, field call, remote security alarm, unmanned aerial vehicle, etc.

Firstly we prepare:

1 x 2 channel long range (5000m), high power receiver with Magnetic Sucker Antenna (S2PUW-DC12-ANT2)

1 x 2-button transmitter (CC-2)

2 x DC12v power supply

1 x power adapter

2 x AC lamps

Some lines

Secondly, see the wiring images below; B is normally open terminal; C normally closed terminal and A is common terminal. Connect power to terminal “+” and “-“. Connect two AC lamps to two terminals “A”

Here is the circuit diagram:

Thirdly, it comes to operation

(1) Setting the receiver as Toggle control mode: turn on the first bit of the dip switch.

Control mode Toggle: Press -> On; Press again -> Off.

(2) Setting feedback function: Turn on the third bit of the dip switch.

Feedback function: can let the user know whether he/she had already connect the transmitter and receiver successfully in such a long distance

(3) Press the big button of the transmitter: Relay 1 turns on (connect A and B, disconnect A and C), the lamp 1 is on.

At the same time, the transmitter exudes a buzzing sound like “D~” which means the lamp 1 is on.

Press the big button again: Relay 1 turns off (disconnect A and B, connect A and C), the lamp 1 is off.

(4) Press the small button of the transmitter: Relay 2 turns on (connect A and B, disconnect A and C), the lamp 2 is on.

At the same time, the transmitter exudes a buzzing sound like “D~” which means the lamp 2 is on.

Press the small button again: Relay 2 turns off (disconnect A and B, connect A and C), the lamp 2 is off.

0020105 (S2PUW-DC12-ANT2&1CC-2) http://www.carymart.com/5000m-wireless-remote-control-kits-c-539.html

Remote control lights

One of our customers is looking for a remote control kit to remote control lights through a hallway at a restaurant. It is meant to signal the server that food is ready in the kitchen. He is looking at the Long Range 2000M 1 CH Momentary Remote Control Kit. This looks like a reliable solution but he have a question... Is there any way of knowing if the light attached the receiver is actually turned on without seeing it. He realize the bulb may blow now and then, but on the whole they need to be sure in the kitchen when they signal the server the light is actually on. He hope he can solve his problem with one of our products.

We recommend this customer to choose model: 0020104 (S1PUW-DC12-ANT2 & CC-2 or CC-1). According to his description, he wants a remote control kit that has two-way function or feedback function. This model is definitely suitable for him to remote control lights at his restaurant. 

The long range remote control kit has feedback function which can let the user know whether he/she had already connected the transmitter and receiver successfully in such a long distance. Two ways working mode, when the receiver gets the signal of transmitter, it will immediately send a return signal to the transmitter.

The remote control kit can be used to control both DC0~28V and AC110~240V equipments.

Notice: The receiver is relay output, not DC/AC power output. Initial state of relay output terminals: Terminals A and B are Normally Open; Terminals A and C are Normally Closed.

 If you want to remote control a DC12V light, do as following:

1) Connect DC12Vpower adapter “+” to terminal “L / +” and Connect DC12V power adapter “-” to terminal “N / -“.

2) Connect Terminal A to the positive pole of the light, connect Terminal B to the positive pole of the power supply, and connect both light and power supply’s negative pole.

If you want to remote control an AC220V light, do as following:

1) Connect DC12Vpower adapter “+” to terminal “L / +” and Connect DC12V power adapter “-” to terminal “N / -“.

2) Connect Terminal A to the light, connect Terminal B to the live wire of the power supply, and connect light and power supply’s neutral wire.

By using this long range remote control kit to remote control lights, the server of the restaurant can easily know whether the food is ready or not in the kitchen. This will bring a lot of convenience for all the members of the restaurant. In addition, such method may let the customers feel more satisfied because it will shorten their time for waiting their food.

If you have the similar problem like this customer, or in other words, if you want to remote control lights, you can enter into our website to choose the remote control kit you like.         

Online shop:www.carymart.com.