Remote control LED lights on riding arena

I built my wife an outdoor riding arena for horse riding. I'm looking at installing 6-8 led flood lights with solar panels to charge 12 volt batteries. Wondering if there was a way I could get a single remote to turn the all lights on and off at the same time. Thanks!

You can buy several receivers and a remote, and install each light to a receiver, then use this remote to turn the all lights on and off at the same time.
We have one-to-many remote control kits. This kind of system includes one-transmitter-to-many-receiver system and one-receiver-to-many-transmitter system. It is often used for controlling two or more electrical devices in different places by one remote; or one electrical device by two or more remotes.
Here are some pictures.

The RF wireless remote control kit is 99 Channel Wireless Transmitter with 24 RF DC Power Receivers remote control system. The working distance can reach 1000M in an open area.

The second RF remote control kit is one transmitter controls 12 receivers system. The maximum working current is 10A.

The third RF wireless remote control systems can remote control six receivers.
With such RF remote control system, you can remote control several device at the same time.
RF remote control shop: www.carymart.com

How to remote control compressor, blower and pump?

I am looking to convert a keyed rotary switch with a remote control switch. The switch has 4 positions, position 1 is all Off. Position 2 lower (turns on compressor) Position 3 Raise (turns on a blower) and Position 4 Drain (turns on a pump). These are turned on individually not all at the same time. The voltage required to power the remote control is AC220V. No current is required to power the devices. The relays are basically open or closed. I would like a 4 channel RF product so I have one channel spare. Can you assist me with what product suits this please.

According to the descriptions from this customer, we recommend him 4 CH Relay output long range waterproof case wireless remote control kit 0020450 (S4PU-AC220-ANT3+1CB-4). Set the receiver S4PU-AC220-ANT3 with Latched mode, then connect compressor to relay 2 in the receiver, connect blower to relay 3 in the receiver, connect pump to relay 4 in the receiver. This remote control kit is composed of a 4-channel receiver and 4-button transmitter that can be used in agriculture automation, industry automation, and home automation. It can control products on land, water and air, especially in a long distance, such as business signs, motorboat, farm, pasture, offshore unmanned operation, field call, remote security alarm, unmanned aerial vehicle, etc. Connected the compressor to the relay 1 of the 4 CH receiver, connect the blower to relay 2 of the 4 CH receiver, connect the pump to the relay 3 of the 4 CH receiver.

There are some remarkable characteristics of this 4 CH Relay output long range waterproof case wireless remote control kit.
Waterproof Function: The 4 channel receiver has waterproof connector and waterproof shell/case, so it can be installed outside.
Working Distance: With external telescopic antenna, this remote control kit can have further working distance. The working distance of the kit can reach 2000m in an open ground. If you stretches the external telescopic antenna, it can have a further working range.
Relay Output: The 4 CH receiver is relay output that can be used to operate both DC and AC equipments. The terminal is NO / NC (normally open / normally closed), which serves as a switch. That means you should also connect a separate power supply to it.
Power Output: Each relay output can work at maximum current 30A. The maximum power of the device is 3000W/110V, 6000W/220V. So it also can be used in agriculture and industry automation, such as long range and high power remote control devices.
Input control terminals: The receiver has four input control terminals, you can connect external devices, sensors, or manual switches to these terminals to control the outputs of receiver.
Three Control Modes: The 4 channel receiver has toggle / momentary / latched working control modes. We use latched control for 4 positions keyed rotary switch.
How to set working control mode?
Set toggle control mode (Press -> On; Press again -> Off): Only connect Jumper-2
Set momentary control mode (Press and hold -> On; Release -> Off): Only connect Jumper-1
Set latched control mode (Press -> On, other relays Off; Press other button -> Off): Disconnect Jumper-1 and Jumper-2

We use 3 lamps to instead the compressor, blower and pump. Now let’s change the keyed rotary switch to remote control switch.
Material Preparation:
Receiver: S4PU-AC220-ANT3
Transmitter: CB-4
3 Lamps
A keyed Rotary Switch
Some Lines

The Wring Diagram:
Just as the following pictures. Connect 3 lamps and 4 positions keyed rotary switch to the 4 Ch receiver. The black wire of the 3 lamps is connected and connect the other black wire to terminal “-“. Connect the red wire of 3 lamps respectively to terminal “A” of relay 1, relay 2 and relay 3. Connect red wire and black wire of the plug respectively to “+” and “-“ of the power. Please note that the red wire used to control lamp1 (compressor) should be connected to terminal A of the relay 1, the red wire used to control lamp2 (blower) should be connected to terminal B of the relay 2, the red wire used to control lamp2 (pump) should be connected to terminal B of the relay 3. The red wire used to turn off the equipments should be connected to terminal B of the relay 3.

Operation:
Press button A of the transmitter, the lamp 1 turns on.

Press button B of the transmitter, the lamp 1 turns off and the lamp 2 turns on.

Press button C of the transmitter, the lamp 2 turns off and the lamp 3 turns on.

Press button D of the transmitter, turn off all of the lamps.

Online shop: http:www.carymart.com

12VDC 6-Button Transmitter for 6 Water Motorbikes

Question from customer:

I would like to find a solution to control 6 water motorbikes (12 V). The idea is that from the beach, I am able to shut down the switch of a user that is getting wild or getting to close to danger. So the longest the control distance is much better.

Answer:

We recommend six 12VDC direct power output receivers (S1XB-DC12-ANT2) with the long distance remote (CB-6). Input power and output power of receiver are same as dc 12v. So it is easy for wiring. The receiver can use the water motorbike’s battery to operate and controlled water motorbike also can get power through receiver. The usage is also very simple. There are 3 working modes setting in the remote control. They are toggle, momentary and latched. But as for you, you have to use toggle mode. Press button, turn on device; Press button again, turn off device.

Working distance of remote and receiver set is 2000m (6000ft) in open field if we add external extended antenna in it.

Controlling 6 water motorbikes , you need 6 receivers. Wire each water motorbike’s motor to each receiver as the following picture shown.

When any of water motorbikes is getting wild or getting to close to danger, you can press any button to stop any of them to prevent from accidents. What’s more, it is the long range remote control which can help you control water motorbikes long distance.

Online shop: www.carymart.com

Hidden TV Set Panels is Controlled by iOS Phone WIFI Controller

Keep from mositure or dust, we usually use slide panels to protect TV set, you can use our utility Smartphone WIFI Controller to open or close slide panels. WLAN WIFI is extensively used nowadays, so we combine remote controller with WIFI network to make useful sort of product.  If you use this WIFI controller, only to use your cell phone as a transmitter, you can control your device within a reliable distance with WLAN.

It is applied in smart home, instruments, equipment control and modern agriculture field. WIFI remote controller controls many kinds of lights, motors, fans, electric doors/windows, aircraft, cars components, toys, rolling blinds, water pumps, winches or other electric devices with voltage AC110~240V or DC0~28V by its normally open and closed terminals.

This WIFI controller supports both 2.1 ~ 4.0 version Android software system and 4.6 ~ 6.1 version iOS software system. And we’d like introduce how to control DC motor under the iOS system. This controller works on the jailbroken iPhone, iPad, iPod Touch. Let’s see the procedure.

Here is the wiring diagram and picture. Motor is connected to common terminal ”B”. And normally open terminal“C” is connected to positive wire. Normally closed terminal “A” is connected to negative wire.

After finishing wiring, we switch on power. The LEDs of “Power”, “Ready” and “Link” are on one by one. We begin to operate.

After wireless network connection, press the icon of WIFI Controller software to turn on it.

There are 3 modes in common use. They are toggle, momentary and latched. But we usually use momentary for motor controlling.

Press and hold button 1, it is the motor’s positive rotation. Release button 1, it is motor’s stop.

Press and hold button 2, it is the motor’s reverse rotation. Release button 2, it is motor’s stop.

Video:

[youtube]http://www.youtube.com/watch?v=DdwwR96LP_Y&feature=youtu.be[/youtube]

Online shop: www.carymart.com

How to Make Simple Home Hot Water Circulating System with Time Delay Function

Question from customer:

I have a hot water circulating pump: 115V AC 0.4A. I want to be able to turn it on from 3 different locations within the house and have it turn itself off after 2 to 3 minutes. Do you have any equipment which will do this?

Answer to this question:

We think this product may be you want – ac1 channel time delay remote module 0020483 (S1DA-AC220-ANT2 & CB-2). The receiver is relay output (normally open and normally closed). Power supply for the receiver and the water pump are different. That means it will not cause electromagnetic interference during water pump operation. With the external extend antenna, the RF signal can pass through walls and doors as well as floors.

The wiring diagram is shown below.

The water pump will be connected to normally open terminals “B&C”.

After wiring, press buttons of “＋” and “－” on the timer, adjust delay time from 0 second to 99 hours. “H” is Hour, “M” is Minute, and “S” is Second. As you said, we set 3 minutes.

So we set “M 0 3”, it means the delay time is 3 minutes. Press big button: Turn on hot water circulating pump. It will stop working by itself after 3 minutes. You can also press small button to turn it off immediately.

According your requirement, one receiver can be paired with 3 transmitters. Any of transmitters can remote control the pump. You are able to turn it on from 3 different locations within your house and have it turn itself off after 2 to 3 minutes by itself.

So your home hot water circulating system will be like this.

Online shop: www.carymart.com

Long Range 2000M DC 12V Remote Control Boat Dock Lights

Question from customer:
I am installing 12v DC lighting on my boat dock. It will operate off a 12v battery with a solar charger. I need a long range on/off remote for the lights. My house is about 400 ft away. I have no AC power at the dock. I was planning on two 12 v lights.

Answer:
We recommend you 2 one-many-system single channel receivers (S1UB-DC12-ANT2) and the long range remote (CB-2). The DC power activated remote is so favorable to you since you have a 12V battery with solar charger. The one-many-system means that you can use one transmitter control more than two receivers. There is no interference between two receivers because they are powered by different adaptors. With external extended antenna, working distance of remote controller extends 1500m, up to 2000m without any obstacles in the open field. So it is believed that the signal can be transmitted from your house to the dock successfully.
We make a presentation of this kind of remote. First, here is the material preparation.
2×1 channel receiver (S1UB-DC12-ANT2)
1×long range transmitter(CB-2)
2×LED light(DC 12V)
2×12V adaptor
Some lines

The wiring is so simple. Each receiver is connected to LED light and adaptor. Switch on the power.


Press big button, turn on the red light(dock light).

Press big button again, turn off red light(dock light).

Press small button, switch on blue light(dock light).

Press small button again, switch off blue light(dock light).


Enjoyable Video:
[youtube]http://www.youtube.com/watch?v=dVBhAciIlnc&feature=youtu.be[/youtube]

Online shop: www.carymart.com

8 Channel DC Remote Control for 24VAC Irrigation Controller

Question from customer:
Hello, I'm hoping you can assist me with product selection. What I'm hoping I can do is use one of your long range remote control systems to control the zones in an irrigation controller. The irrigation controller and irrigation zones operate on 24VAC.
I think that your product S8CA-DC12-ANT2+CB-8 would work for my needs if the relays were 24V AC instead of 120V AC. Attached is a diagram of how I'm envisioning it all working.

Answer:
8 Channel long range remote control is designed to be normally open and close connection. So all relays in this receiver can work at 24VAC. We add external extended antenna in the receiver in order to extend the range of remote controlling. It is estimated that the working distance of remote reach 2000M in the open filed.

There is 8 channel for your irrigation zones. According to your diagram, you can wire the irrigation zones and receiver as follow.

We supply receiver with other power so that no interference will generate between remote control and irrigation controller.
There are 8 working modes. You can choose any of them as you want. You can use one transmitter to open and close irrigation zones remotely.
Online shop: www.carymart.com

15 Channel DC Remote Control Code Learning/Deleting and Remote Operation

We designed 15 channel DC mixed- mode remote control to satisfy customers’ more need. It is still wireless control and easy to install. It can control lights, motors, fans, electrically operated doors, locks, windows, blinds, cars or other appliances with voltage AC110~240V or DC0~28V. You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless signal can pass through walls, floors and doors. It includes toggle, momentary, latched and mixed working modes.

The following operation is the code learning and deleting and remote control operation. At first, we should prepare material.

1×15 channel RF receiver

1×15-button transmitter

4× AC lamp(They will be connected at channels at random, just for demonstration purposes, actually you can wire 15 lamps)

Power adaptor

You can follow the wiring diagram for its wiring. Then switch on power.

Deleting code:

We should delete all stored codes firstly. Press and hold learning button for 3 seconds, then release button after buzzer sounds 5 times. All stored codes are deleted successfully.

There are 15 channels in receiver. So it has 15 working modes in it. But we only show four common operation modes here. They are toggle, momentary, latched and toggle+ momentary+latched modes.

Learning mode:

Press and hold learning button, the receiver is in the status of learning after buzzer sounds 1 time. Press corresponding button of each working mode, for example, button 3 for toggle mode, button 1 for momentary mode, button 2 for latched, and button 9 for one of mixed modes (Toggle+ Momentary+Latched modes)

Toggle mode learning and operation:

Press and hold learning button, the receiver is in the status of learning after buzzer sounds 1 time. Press button 3 at once, buzzer sounds 3 times, the receiver learns Toggle mode successfully.

Toggle mode operation:

Press any button to control the corresponding lamp. For example, press button 1, turn on lamp 1; press button 1 again, turn off lamp 1...

After operation of each mode, we should delete previous stored codes in advance, and then start to learning next working mode.

Momentary mode learning and operation:

Do as toggle mode learning, Press and hold learning button, the receiver is in the status of learning after buzzer sounds 1 time. Press button 1 at once, buzzer sounds 3 times, the receiver learns Momentary mode successfully.

Press any button to control the corresponding lamp. For example, press and hold button 6, turn on lamp 6; release button 6, turn off lamp 6...

Latched mode learning and operation:

Deleting momentary learning code, press and hold learning button, the receiver is in the status of learning after buzzer sounds 1 time. Press button 2 at once, buzzer sounds 3 times, the receiver learns latched mode successfully.

Press any button to control the corresponding lamp. For example, press button 1, turn on lamp 1, other lamps are off; press button 6, turn on lamp 6, other lamps are off...

Mixed mode learning and operation: (Toggle+ Momentary+Latched modes)

Deleting latched learning code, press and hold learning button, the receiver is in the status of learning after buzzer sounds 1 time. Press button 9 at once, buzzer sounds 3 times, the receiver learns Toggle +Momentary + Latched mode successfully. (1~5 channel is T mode; 6~10 channel is M mode; 11~15 channel is L mode)

1~5 channel (T mode): press button 1, turn on lamp 1; press button 1 again, turn off lamp 1.

6~10 channel (M mode): press and hold button 6, turn on lamp 6; release button 6, turn off lamp 6.

11~15 channel (L mode): press button 11, turn on lamp 11, other lamps are off; press button 12, turn on lamp 12, other lamps are off.

Video:

[youtube]http://www.youtube.com/watch?v=eZimbg4UjC8&feature=youtu.be[/youtube]

Online shop: www.carymart.com