1 Channel 24V RF Remote Controller Controls Ignition of a Beacon

A beacon is a light or fire on the hill or tower which acts as a signal or a warning to help guide navigator to their destination with safety. One customer said, “I'm looking for a system which can remotely control (200m max) ignition of a beacon in 24 V dc”.

We recommend him the model of single channel 24V power output RF remote (S1X-DC24-ANT2 +1CB-2). Single channel is for one device. 24V direct power output can supply power directly to the device which is controlled. User can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through walls, floors and doors. The receiver, which mounts long range magnetic antenna, pairs with long distance transmitter to reach to 2000m in the open field.

There are 3 control modes. They are Toggle, momentary and latched.
Setting control mode Toggle: Only connect Jumper-2.
1) Press big button: Turn on the relay.
Press big button again: Turn off the relay.
2) Setting control mode Momentary: Only connect Jumper-1.
Press and hold big button: Turn on the relay.
Release big button: Turn off the relay.
3) Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.
Press big button: Turn on the relay.
Press small button: Turn off the relay.
As regards controlling beacon, we suggest the latched mode. Press big button to turn on beacon light, press small button to turn off the light.
For the wiring, it is so simple. The following picture shows. Lamp is connected to terminals A&B on the receiver. The receiver should be supplied 12V power. There is no need to supply power to lamp because lamp can get power from the receiver.


Online shop: www.carymart.com

1 Channel DC 12V Wireless Remote Control Modem On and Off

Question from customer:
I want to use your system to remote control turn on / off the power of the modem. I go from my office on the third floor of our home to the basement in order to turn off and disconnect the power to the modem. Then after a few minutes I reverse the process and reestablish the power to the modem and turn the modem on. The modem is power by an AC Adaptor (INPUT = 120-240V OUTPUT = 12V ).

Answer:
We recommend the model of 1 channel DC long range remote control kit (S1X-DC12-ANT2+1CB-2) to you. It can wireless control electric devices and  is easy to install. With direct power output, it means that you don’t need to supply power to the controlled device. It is capable of controlling lights, motors, fans, electrically operated doors/locks/windows/blinds/cars or other appliances.
You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through walls, floors and doors. We add external extended antenna to it. The antenna can extend the controlling range to 2000M. So you can rest assured that signal can get through any obstacles to reach modem at your home.

As for your modem is powered by ac power, so you should connect the output of your AC Adaptor (12V) to two terminals + and - of this receiver, then connect two terminals A and B to your modem, then you can use our remote CB-2 to turn on / off the power of the modem.
You can set “Latched Mode”.
Press big button, turn on the modem.
Press small button, turn off the modem.

Online shop: www.carymart.com

1 Channel 12VDC RF Remote Control Group for Nitrogen Purging System

Question from customer:
I need a remote valve setup for a nitrogen purging system.The valve is 100volt 10amp that needs to be controlled by latching switch setup. I’ve seen many setups everywhere that will work but my problem is that I need some sort of indications, such as a led lamp or something at the remote to verify whether the valve is open or not. Do you have something like this available?
Feasible solution:
We found a solution to solve your problem. We also made a simulation test.
You need feedback to the remote or another receiver with a signal light to verify remotely that the valve is open. We’d like to prepare two sets of remote control and make them a remote control group. The main system is 1 channel 12VDC output receiver (S1XL-DC12)+ long range transmitter (CB-2). The secondary system is still 1 channel 12VDC output receiver (S1XL-DC12) , but we use dc triggered transmitter (CB-2V, triggered method DC power 5~28V input), which is applied for one device controlling another device. That is to say, the transmitter will send out RF signal to receiver as long as it gets a 5~28V voltage from a device.
The following picture is the material preparation.

When you add the external extended antenna, you will make the remote controller working distance to 2000M in the open air.

Here is the wiring diagram.

The wired transmitter (CB-2) will work with Receiver 1 as one group. The wireless transmitter (CB-2V) will work with Receiver 2 as another group. We have a wired remote transmitter at the first receiver that it will remotely turn on a lamp at the second receiver near the wireless transmitter.

Operation:
Press big button of wireless transmitter (CB-2), send "ON" RF signal to the first receiver, turn on lamp 1(blue lamp) and trigger wired transmitter (CB-2V), wired transmitter switch on lamp (red lamp) on the second receiver.


Press small button of wireless transmitter (CB-2), send "OFF" RF signal to the first receiver, turn on lamp 1 (blue lamp) and trigger wired transmitter (CB-2V), wired transmitter switch off lamp 2 (red lamp) on the second receiver.


We can get feedback through red lamp to verify whether the controlled device (Blue lamp) is working or not.
Video:
[youtube]http://www.youtube.com/watch?v=BTCYENYhrb4&feature=youtu.be[/youtube]

Online shop: www.carymart.com

1 Channel AC 220V Delayed Remote Unit Activated Hot Water Circulator Pump

Question from customer:

I want to use one device to turn on a hot-water circulator in my home for 15 minutes&then have it automatically turn off. I live in a 2 story wood home&the hot-water circulator is in the basement-maybe a distance of about 30 ft away through drywall&wood flooring. Will it work over this distance? Would I need to order a telescopic antenna?

Answer:

We think this product may be suitable for you– 1 channel ac delayed remote unit (0020483 S1DA-AC220-ANT2+CB-2). This kind of remote unit is with time delay timer, which you can adjust time according to your requirement. With external extend magnetic antenna, working distance of transmitter and receiver will reach 2000m/6000ft (theoretically).So you don't have to order telescopic antenna.

Wiring program is as follow:

We connect delayed remote unit to circulator pump. The receiver is relay output (normally open and normally closed). Power supply for the receiver and the water pump are different. That means it will not cause electromagnetic interference during water pump operation.

Operation:

Press big button: Turn on relay (connect B and C, disconnect A and B).
After delay time: Turn off relay by itself (disconnect B and C, connect A and B).
Press small button: Turn off relay immediately, no need to wait for delay time.

Press buttons of “＋” and “－” on the timer, adjust delay time from 0 second to 99 hours. “H” is Hour, “M” is Minute, and “S” is Second.
As your requirement, you can set “M 1 5”, it means the delay time is 15 minutes. After working for 15 minutes, it will be off automatically. Then the circulator pump stops pumping.

Online shop: www.carymart.com

1 Channel 12V Voltage Output Remote Control Unit Switch Motor On/ Off—2000M

Question from Customer:

I seek a transmitter-receiver 12V to run a small motor away from 300~500 meters with operating on off.

Answer:

Our suggestion is this 1 channel 12V voltage output remote control gadget (S1X-DC12-ANT2 & CB-2). Single channel is for one device. 12V direct power output can supply power directly to the device which is controlled. User can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through walls, floors and doors. The receiver, which mounts long range magnetic antenna, pairs with long distance transmitter to reach to 2000m in the open field.

There are 3 control modes. They are Toggle, momentary and latched.

Setting control mode Toggle: Only connect Jumper-2.

1) Press big button: Turn on the relay.

Press big button again: Turn off the relay.

2) Setting control mode Momentary: Only connect Jumper-1.

Press and hold big button: Turn on the relay.

Release big button: Turn off the relay.

3) Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.

Press big button: Turn on the relay.

Press small button: Turn off the relay.

As regards controlling motor on and off, we suggest the latched mode. Latched mode is really favorable for long range controlling because big button on transmitter is for ON, small button is for OFF. If you want to turn on motor, you can press big more for many times to make sure that the motor is on. If you want to turn off motor, you can press small more for many times to make sure that the motor is off.

For the wiring, it is so simple. The following picture shows. Motor is connected to terminals A&B on the receiver. The receiver should be supplied 12V power. There is no need to supply power to motor because motor can get power from the receiver.

Online shop: www.carymart.com